Thursday, July 25, 2013

Posted by Unknown |
How to Repair Selenium Light Meters

Selenium is a nonmetallic element used in the photography trade. A selenium meter uses selenium to measure the exposure of a photograph being taken with a camera. Located just above the optical lens, the meter is very sensitive, and any dirt or dust on it can interfere with its ability to perform. You can repair a selenium meter in your camera as long as you are very careful and handle the meter with great care.

Instructions

    1

    Take off the film advance latch by pulling it up and away from the camera.

    2

    Open the back of the camera and push the spindle of the rewind up and out of the case. The rewind is on the far left side of the camera when you are looking at it from behind.

    3

    Remove the tiny screws holding the top cover of the camera in place. You will have one at each end of the cover and possibly one along the front.

    4

    Take out the two small screws holding the meter in place on top of the camera. Gently lift the meter out of the camera and set it on a clean surface.

    5

    Brush any dust or dirt from the meter using the lens brush. You should also clean the area where the meter was.

    6

    Rub off any persistent marks with a cotton swab and a very small amount of solvent.

    7

    Replace the meter inside the camera and insert the screws into the camera to hold it in place.

    8

    Put the top cover back on and insert the screws. Put the rewind and advance controls back on as well.


How to Repair Selenium Light Meters

Selenium is a nonmetallic element used in the photography trade. A selenium meter uses selenium to measure the exposure of a photograph being taken with a camera. Located just above the optical lens, the meter is very sensitive, and any dirt or dust on it can interfere with its ability to perform. You can repair a selenium meter in your camera as long as you are very careful and handle the meter with great care.

Instructions

    1

    Take off the film advance latch by pulling it up and away from the camera.

    2

    Open the back of the camera and push the spindle of the rewind up and out of the case. The rewind is on the far left side of the camera when you are looking at it from behind.

    3

    Remove the tiny screws holding the top cover of the camera in place. You will have one at each end of the cover and possibly one along the front.

    4

    Take out the two small screws holding the meter in place on top of the camera. Gently lift the meter out of the camera and set it on a clean surface.

    5

    Brush any dust or dirt from the meter using the lens brush. You should also clean the area where the meter was.

    6

    Rub off any persistent marks with a cotton swab and a very small amount of solvent.

    7

    Replace the meter inside the camera and insert the screws into the camera to hold it in place.

    8

    Put the top cover back on and insert the screws. Put the rewind and advance controls back on as well.



  • How to Repair & Replace Light Switches - HomeTips HomeTips

    www.hometips.com/repair-fix/replace-light-switch.html

    If a light doesnt work and you suspect that the switch may be broken, do the following: 1) Turn off the power to the lights circuit. 2) Remove the switchs ...


  • How To Check Continuity With Ohmmeter - Appliance Repair Forum

    forum.appliancepartspros.com Appliance Repair HelpLast updated: Mar 19, 2008 10 posts First post: Jan 24, 2008

    Copyright AppliancePartsPros.com, Inc. Hi! In this article, we'll be talking about the basics of performing continuity checks using an ohmmeter ( need one ?). Grab your


  • How to test a light bulb - Ohm Check DIY Electrical Articles ...

    www.ohmcheck.com/content.php?153-How-to-test-a-light-bulb

    Learn how to test light bulbs, including LED and fluorescent bulbs, never throw a good one away again.


  • DIY Auto Repair Help - Car Maintenance, Troubleshooting, How To ...

    autorepair.about.comFix It Yourself Troubleshooting DIY Repairs My Car Won't Start

    You can do your own auto repairs by following out easy step-by-step do-it-yourself tutorials which show you how to diagnose, troubleshoot, repair, fix, modify and ...


  • How to Use Selenium for Health eHow

    www.ehow.com Diet & Nutrition Nutritional Supplements

    Although your body only needs small doses of selenium for good health, if the fruits and vegetables you eat were grown in selenium depleted soil, you may not be ...


  • Electrical Repairs - How To Information Page 1 eHow

    www.ehow.com Home & Garden Home Repair & Maintenance

    Don't just sit there scratching your head, find useful info on Electrical Repairs on eHow. Get essential tips and learn more about everything from Instructions for ...


  • How To Install Replace Mass Air Flow Meter Sensor Chevy

    www.youtube.com/watch?v=qlKpq2vHfIE

    http://www.1aauto.com/1A/air-flow-met... 1A Auto shows you how to repair, install, fix, change or replace a broken, worn out, or damaged air flow sensor ...


  • How To Fix

    www.howtofix.org

    If you're like me, you don't particularly like that first few minutes of taking a shower when the water is running and you're waiting for it to warm up.


  • How to Repair a Broken Light Fixture HomeTips

    www.hometips.com/repair-fix/light-fixture-broken.html

    When a single light doesnt work, the problem is almost always either the bulb, the circuit breaker (or fuse), or the switch. The first and most obvious solution is ...


  • How to Test a car starter using an amp meter Auto

    diy-auto-repair.wonderhowto.com/how-to/test-car-starter-using-amp...

    How to Test a car starter using an amp meter. The starter on your car's health is directly related to how many amps it pulls from the battery. This video will show ...

0 comments:

Post a Comment